EtherSens Control - Process Informatik Entwicklungsgesellschaft mbH

EtherSens Control

Capture Dig/Analog-IO +++ Log Dig/Analog-IO +++ PLC fault message-dispatch +++ PLC-data logging/saving +++ implement control-tasks +++ Datalogger with web-server +++ Digital/analogue onboard-IO

Supply voltage: 24V DC
12 x digital IN or OUT 24VDC 400mA
free config with software
4 x analog IN 0-5V
opt. with ext.Shunt 0/4-20mA
opt. with ext. restistance 0-10/24/50V
4 x analog OUT 0/4-20mA (24V)

LAN and WIFI-interface integrated
function to the same time

New: Ethersens ProSuite with optional touch-graphic-display and IO-bus

Features:

Sends alarm-messages controlled by the PLC
- Receiver in the PLC deposited, so ONLINE replaceable
- Messages in the PLC deposited, so ONLINE replaceable

more...

variants:

435,00 € plus VAT. and shipping

ARTNR: 9200-AD-24V
EtherSens Control 24V Analog-/Digital-IO V1.0

EAN number:		4260363244336
HS-code:		85423190
Weight:		0.2 kg

EtherSens configurator

Configure the EtherSens device for your requirements.

New: Ethersens ProSuite with optional touch-graphic-display and IO-bus

Features:

Sends alarm-messages controlled by the PLC
- Receiver in the PLC deposited, so ONLINE replaceable
- Messages in the PLC deposited, so ONLINE replaceable
Communication with a controller via optional IO-modules, LTE or via network S7-TCPIP RFC1006
- S7-PLC over S7-LAN-module
- S5-PLC over S5-LAN++-module
Solve control-tasks via integrated logic-module
Implementation of different protocols, for e.g. L1-bus-communication via RFC1006, Modbus
Coupling of multiple devices to a network
Coupling with WinCC and access to process values

Application-examples (only german language):

Capture data and control independently
Produkbild

Apply small control tasks of your systems with EtherSens-Control-devices. Determine switching points where the device is running to respond. Depending on the parameterization, an email or SMS notification (depending on the device-configuration) or the device automatically controls via the optional IO-modules (analog / digital / relay).

Data acquisition/logging
Produkbild

By connecting a line-recorder to the EtherSens-device anyone without network-knowledge can visually capture and further process the log.

Relaycontacts 230VAC/16A directly over WIFI/LAN
Produkbild

Switch with the EtherSens Control with relay-output easily and directly over LAN or WIFI up to 230VAC/16A, switchable over web-browser, TCP/IP-protocol or PLC-controlled. At the same time you monitor the switching-states on the optional SD-card or on the FTP server.

Data backup S5-PLC on FTP-Server
Produkbild

S5-PLC triggered DB-backup/-restore without additional PC via PG-socket and Ethernet on FTP-server

Data backup S5-PLC on FTP-server via dig. IO
Produkbild

Via digital input triggered DB-backup/-restore without additional PC via PG-socket and Ethernet to FTP-server

Data backup S5-PLC on SD-card
Produkbild

S5-PLC triggered DB-backup/-restore without additional PC via PG-socket and Ethernet on SD-card

Data backup S5-PLC on SD-card via dig. IO
Produkbild

Via digital input triggered DB-backup/-restore without additional PC via PG-socket and Ethernet to SD-card

Data backup S5-PLC on USB-stick
Produkbild

S5-PLC triggered DB-backup/-restore without additional PC via PG-socket and Ethernet on USB-stick

Data backup S5-PLC on USB-stick via dig. IO
Produkbild

Via digital input triggered DB-backup/-restore without additional PC via PG-socket and Ethernet to USB-stick

Data backup S7-PLC PN-port on FTP-server
Produkbild

S7-PLC triggered DB-backup/-restore without additional PC via PN-port on FTP-server

Data backup S7-PLC PN-port on FTP-server via dig. IO
Produkbild

Via digital input triggered DB-backup/-restore without additional PC via PN-port to FTP-server

Data backup S7-PLC PN-port on SD-card
Produkbild

S7-PLC triggered DB-backup/-restore without additional PC via PN-port on SD card

Data backup S7-PLC PN-port on SD-card via dig. IO
Produkbild

Via digital input triggered DB-backup/-restore without additional PC via PN-port to SD-card

Data backup S7-PLC PN-port on USB-stick
Produkbild

S7-PLC triggered DB-backup/-restore without additional PC via PN-port to USB-stick

DB-Backup/Restore S7-PLC PN-port on USB-stick via dig. IO
Produkbild

Via digital input triggered DB-backup/-restore without additional PC via PN-port to USB-stick

Data backup S7-PLC over MPI/Profibus on FTP-server
Produkbild

S7-PLC triggered DB-backup/-restore without additional PC via MPI/Profibus on FTP-server

Data backup S7-PLC over MPI/Profibus on FTP-server via dig. IO
Produkbild

Via digital input triggered DB-backup/-restore without additional PC via MPI/Profibus to FTP-server

Data backup S7-PLC over MPI/Profibus on SD-card
Produkbild

S7-PLC triggered DB-backup/-restore without additional PC via MPI/Profibus on SD-card

Data backup S7-PLC over MPI/Profibus on SD-card via dig. IO
Produkbild

Via digital input triggered DB-backup/-restore without additional PC via MPI/Profibus to SD-card

Data backup S7-PLC over MPI/Profibus on USB-stick
Produkbild

S7-PLC triggered DB-backup/-restore without additional PC via MPI/Profibus on USB-stick

Data backup S7-PLC over MPI/Profibus on USB-stick via dig. IO
Produkbild

Via digital input triggered DB-backup/-restore without additional PC via MPI/Profibus to USB-stick


Supply voltage:	24V DC +/- 20%
Power consumption:	10 watt (without possibly switched outputs)
Display:	WEB-Browser 1 status LED bicolor
Handling/Configuration:	WEB-Browser
Interfaces:	12 x digital-IO switchable as - Input (24VDC max. 8k2 (PullUp external) / min. 1.6mA ) or - Output (24VDC 400mA) 4 x Analogue Input V1.0 (0-5V) - opt. with ext.Shunt 0/4-20mA - opt. with ext. restistance 0-10/24/50V 4 x Analogue Input V1.1 (switchable between U, I, differential) - Free configurable voltage-inputs with full 15-bit resolution: 0-50V, 0-40V, 0-20V, 0-10V, 0-5V, 0-4V, 0-2V, 0-1V, 0-0,5V, 0-0,25V - Free configurable differential voltage-inputs with full 15-bit resolution AI1 <-> AI2 and AI3 <-> AI4: +/-50V, +/-40V, +/-10V, +/-5V, +/-4V, +/-2V, +/-1V, +/-0,5V, +/-0,25V - Free configurable current-inputs with full 15-bit resolution: 0-20mA, 4-20mA - sample-rate of AD-converter can be selected: - fast = fast conversion / short precision - balanced = middle conversion / middle precision - exact = slow conversion / high precision - Measuring ranges after changing are calibrated to: - offset for 0V / 0mA - slope of voltage / current (ideal for end of measuring-range / full-scale) - Relative values can be configured to the original voltage- / current-values. For e.g.: On the voltage-input 10V were measured 5V, relative minimum = 0 kg, relative maximum = 100 kg, so the displayed-value is 50 kg Is minimum and maximum configured as 0 the measured voltage- / current-value will be displayed. 4 x analogue Output 0/4-20mA (source-power 24V) Slot for microSD Antenna-connector SMA(f) (2.4 GHz IEEE 802.11b/g) 10/100BaseTX RJ45-ethernet-plug Button for factory settings
Overvoltage category:	CAT IV
Insulation value network <=> mains voltage:	1,5 KV
Operating temperature:	0 - 55°C
Case:	ABS-plastic case V0
Dimensions:	100 x 112 x 45 mm

Scope of delivery:	EtherSens Control WIFI-stub-antenna

All prices plus costs of delivery, shipping insurance and VAT.

extensions:

9230-AIO
Extension Analog-IO V1.0
Extension-board for EtherSens-devices 4 x analog IN 0-5V opt. with ext.Shunt 0/4-20mA opt. with ext. restistance 0-10/24/50V 4 x analog OUT 0/4-20mA (24V) Power consumption: 4W

by e-mail

128,00 €
plus VAT. and shipping

9230-EI2C-5V
Extension with ext. galv. separated I2C 5V
Extension-board for EtherSens-devices with galvanic separated external I2C-connector for 5V Power consumption: 2W

by e-mail

117,00 €
plus VAT. and shipping

9230-LTE
Extension LTE-modem
LTE-modem-board for EtherSens-devices Send/receive of SMS-messages Communication from/into internet Power consumption: 6,5W

by e-mail

264,00 €
plus VAT. and shipping

9230-ENERGY
Extension Energy-IO
Extension-board for EtherSens-devices Energy-analysis (EN 50470-1 EN 50470-3) L1, L2, L3, N realtime analysis Up to 8000 measurements / second Hz / cos phi / power-factor Energy consumption kWh For Rogwski-coils up to 0,5V

by e-mail

352,00 €
plus VAT. and shipping

9220-U-I-BOX
U-I-box for EtherSens
max. 1000V DC / 40A 24V DC supply 20cm power-cable 4mm2 with Amphenol-plug I2C-connection 1m

by e-mail

158,00 €
plus VAT. and shipping

9220-SONNE
Sun-light-sensor for EtherSens
max. 220k Lux (switchable ranges) 3.3V DC supply (from I2C-interfaceport) I2C-connection 1m

by e-mail

105,00 €
plus VAT. and shipping

9220-GYRO-SENS-312
Gyro-Sensor 312 for EtherSens
Measuring range: ±1.5g / ±3g / ±6g / ±12g 3.3V DC supply (from I2C-interfaceport) I2C-connection 1m

by e-mail

105,00 €
plus VAT. and shipping

9220-GYRO-SENS-313
Gyro-Sensor 313 for EtherSens
Measuring range: ±0.5g / ±1g / ±2g / ±4g 3.3V DC supply (from I2C-interfaceport) I2C-connection 1m

by e-mail

105,00 €
plus VAT. and shipping

9220-T-LF-D
Temp./humidity/air-pressure for EtherSens
Measuring range: Temperature: -40 ...+85°C Humidity: 0...100% relative Feuchte Pressure: 300...1100 hPa 3.3V DC supply (from I2C-interfaceport) I2C-connection 1m

by e-mail

105,00 €
plus VAT. and shipping

9220-SEG-ANZEIGE
Segment-display for EtherSens
4 Digit 14 segment-display WHITE 0,56" high in wall-mounting case 5V DC supply (from I2C-interfaceport) I2C-connection

by e-mail

158,00 €
plus VAT. and shipping

9230-EI2C-3.3V
Extension with ext. galv. separated I2C 3.3V
Extension-board for EtherSens-devices with galvanic separated external I2C-connector for 3.3V Power consumption: 2W

by e-mail

117,00 €
plus VAT. and shipping

9230-MIO-485
Extension RS485-IO
Extensionboard for EtherSens-devices V1.0 for RS485 Power consumption: 2W

by e-mail

158,00 €
plus VAT. and shipping

9230-MIO-TTY
Extension TTY-IO
Extensionboard for EtherSens-devices V1.0 for TTY (incl. 2x current-sources) Power consumption: 2W

by e-mail

158,00 €
plus VAT. and shipping

9230-DIO
Extension Digital-IO
Extension-board for EtherSens-devices 12 x digital IN or OUT 24VDC 400mA free config with software Power consumption: 4W

by e-mail

191,00 €
plus VAT. and shipping

9230-GG
Bigger Case
Width 90mm instead of 45mm

by e-mail

106,00 €
plus VAT. and shipping

9230-RIO-24V
Extension 24V Relay-IO
Extension-board for EtherSens-devices Supply voltage: 24V DC 4 x relay-OUT 230VAC/16A Power consumption: 4W

by e-mail

170,00 €
plus VAT. and shipping

9230-RIO-230V
Extension 230V Relay-IO
Extension-board for EtherSens-devices Supply voltage: 230V AC 4 x relay-OUT 230VAC/16A Power consumption: 2,5W

by e-mail

227,00 €
plus VAT. and shipping

9230-NT-230V
Power-supply-rack-unit 230V
Input voltage: 100 - 240VAC 50-60Hz Output voltage: 24V DC Power: 4W

by e-mail

68,00 €
plus VAT. and shipping

9230-AIO-V1.1
Extension Analog-IO V1.1
Extension-board for EtherSens-devices 4 x Analogue Input (switchable between U, I, differential) 4 x analog OUT 0/4-20mA (24V) Power consumption: 4W

by e-mail

149,00 €
plus VAT. and shipping

9230-MIO-422
Extension RS422-IO
Extensionboard for EtherSens-devices V1.0 for RS422 (4-wire) Power consumption: 2W

by e-mail

158,00 €
plus VAT. and shipping

9230-MIO-232
Extension RS232-IO
Extensionboard for EtherSens-devices V1.0 for RS232 (RxD, TxD) Power consumption: 2W

by e-mail

158,00 €
plus VAT. and shipping

9230-USB
Extension USB-port
USB-port for EtherSens-devices (data storage) Extension for: - DB-backup/restoure-function - CSV-recording Maximum current: 200mA for 5V DC

by e-mail

105,00 €
plus VAT. and shipping

accessories:

9391.1
24V DC power-supply unit 625mA
Primary 110V - 240 VAC Euro+USA-plug

by e-mail

59,00 €
plus VAT. and shipping

9230-SD-32
Micro-SD-card 32GB
for EtherSens-devices SDHC class 10

by e-mail

27,00 €
plus VAT. and shipping

9230-ANT-WAND
Stationary Wifi-antenna for wall fastening
for EtherSens-devices, cable length: 5m for indoor and outdoor use incl. bracket

by e-mail

84,00 €
plus VAT. and shipping

9240-SDÜ
Option Safe S7-PLC-data-transmission
Function extension for recognition of save data-transmission by toggle bit or counters in the S7-PLC. In case of a failure, a default configuration is mapped to the outputs.

by e-mail

99,00 €
plus VAT. and shipping

9636-TCPIP.1M
Patch-cable 1m, Cat5e, shielded
RJ45 plug <=> RJ45 plug, 1:1

by e-mail

15,00 €
plus VAT. and shipping

9352-WLAN-ANT
Magnetic base antenna
for S7-WLAN-Bridge, WLAN-Klemme, EtherSens cable length: 3m

by e-mail

83,00 €
plus VAT. and shipping

9636-TCPIP.02M
Patch-cable 0.25m, Cat5e, shielded
RJ45 plug <=> RJ45 plug, 1:1

9636-CROSS
Cross-cable 3m Cat5+, shielded
RJ45 plug <=> RJ45 plug, twisted pinning

9636-TCPIP
Patch-cable 3m, Cat5+, shielded
RJ45 plug <=> RJ45 plug, 1:1

9230-LTE-ANTW
Stationary LTE-antenna for fixed mounting
for EtherSens/CONNECT-devices LTE-modem for indoor and outdoor use cable length: 2m

by e-mail

163,00 €
plus VAT. and shipping

EtherSens

EtherSens Energy
Collect energy data +++ Log energy data +++ PLC fault message dispatch +++ PLC data logging/saving +++ Implement control tasks +++ Configuration via webinterface

EtherSens Basic
PLC fault message dispatch +++ PLC data logging/saving +++ implement control tasks +++ Universal solution per task +++ Web page parameterization +++ EtherSens Basic

EtherSens Oxygen
Capture of gas-values +++ Monitor of gas-values +++ PLC-fault messaging +++ PLC-data logging/saving +++ Convert control tasks

MONI mobile netanalyser EN 50470-1 / EN 50470-3
load studies +++ energy checks +++ collect energy data +++ Log energy data +++ PLC fault message dispatch +++ PLC-data logging/saving +++ implement control-tasks +++ EN50470-1 / EN50470-3

EtherSens ProSuite
The complete and flexible solution for monitoring, controlling and analyzing industrial processes

EtherSens ProSuite with touch-display
The complete and flexible solution for monitoring, controlling and analyzing industrial processes

EtherSens ProSuite LTE
The complete and flexible solution with LTE for monitoring, controlling and analyzing industrial processes

EtherSens ProSuite LTE with touch-display
The complete and flexible solution with LTE for monitoring, controlling and analyzing industrial processes

All prices plus costs of delivery, shipping insurance and VAT.

9101.2
OSM sensor
Plum - O2 - Cell

by e-mail

211,00 €
plus VAT. and shipping

9352-LANCON
S7-LAN connector for Siemens S7 PLC controller Obsolete
Successor: S7-LAN++ connector for Siemens S7 Controller (Art.No: 9352-LANCON++)
Network-connection for the S7-200/300/400-PLC +++ S7-adapter PPI/MPI/PROFIBUS +++ Of developer and manufacturer +++ Smallest Ethernet-gateway S7 +++ Network for each S7-PLC +++ Fast commissioning +++ Replacement for CP343-1/443-1

by e-mail

0,00 €
plus VAT. and shipping

9230-SD-32
Micro-SD-card 32GB
for EtherSens-devices SDHC class 10

by e-mail

27,00 €
plus VAT. and shipping

9352-WLAN-ANT
Magnetic base antenna
for S7-WLAN-Bridge, WLAN-Klemme, EtherSens cable length: 3m

by e-mail

83,00 €
plus VAT. and shipping

9359-LAN
S5-LAN++
Industrial Ethernet <> S5 PD-interface (TTY) Including Gateway Plus and S7-TCP / IP functions

EtherSens Control

Capture Dig/Analog-IO +++ Log Dig/Analog-IO +++ PLC fault message-dispatch +++ PLC-data logging/saving +++ implement control-tasks +++ Datalogger with web-server +++ Digital/analogue onboard-IO

Application-examples (only german language):

extensions:

accessories:

Differences

EtherSens

Automatic-mode

Main downloads

Versionstory

Other downloads

Documentation

Extension

Support-videos

Support

Newsletter

About us