V2.55 V2.54 V2.53 V2.52 V2.51 V2.50 V2.49 V2.48
V2.47 V2.46 V2.45 ! V2.44 ! V2.43 V2.42 V2.41 V2.40
Fehler bei Install-Shield bzgl. S7-GATE
Error in Install-Shield for S7-GATE
Gerätetyp S7-GATE integriert
Doppelte Meldungsanzeige nach erfolgloser Suche behoben
Device-type S7-GATE integrated
Double message-display after unsuccessful search fixed
PPI-Treiber erweitert, sodass dieser nun auch für ältere S7-200-Steuerungen "PPI" und "PPI advanced" genutzt werden kann. PLCVCom wird bei Siemens nicht mehr benötigt
Konfigdialog für Firmware mit neuen PPI-Betriebsarten erweitert
Fehler behoben, wodurch es bei USB-Kommunikation über Siemens-Software zum Verbindungsabbruch kommen kann
Routing für LAN-Geräte verbessert
Busparameter-Anzeige im Gerätestatus-Dialog angepasst
Fehler beim Laden von Bausteinen in S7-200-Steuerungen mit PPI behoben
PPI-driver expands, so that this can now be used for older S7-200 controls "PPI" and "PPI Advanced". PLCVCom is no more needed for Siemens
ConfigDialog for firmware with new PPI-operating-modes expanded
Fixed bug, which can lead to USB-communication via Siemens-software for connection cancellation
Routing for LAN-devices improved
Bus parameter display in the device status dialog adapted
Fixed bug when loading blocks in S7-200-controllers with PPI
Interne Revision
Internal revision
Enthaltene Firmware: S7-LAN V2.61, MPI-LAN V2.86, S7-USB 1.34, MPI2/USB V2.82, MPI/DB-Scan V1.02
Verbindungstest zu USB-/LAN-Produkten integriert
LAN-Kommunikation bei OpenVPN-Verbindung im TAP-Mode integriert
Laden der Werkseinstellungen übernahm nicht alle Parameter
Backup/Restore-Funktion sichert jetzt auch Konfiguration der Module (Variablen Steuern, NTP, Gateway, IP-Device to S7) des S7-LAN/MPI-LAN
Verbindungsaufbau über USB zu Panel und Setzen der Bus-Adresse überarbeitet
Included firmware: S7-LAN V2.61, MPI-LAN V2.86, S7-USB 1.34, MPI2/USB V2.82, MPI/DB-Scan V1.02
Connection test to USB-/LAN-products integrated
LAN-communication with OpenVPN-connection integrated in TAP-mode
Loading the factory settings did not apply all parameters
The backup / restore function now also saves the configuration of the modules (variables control, NTP, Gateway, IP-Device to S7) of S7-LAN/MPI-LAN
Establishing a connection via USB to panel and setting the bus address revised
Enthaltene Firmware: S7-LAN V2.60, MPI-LAN V2.85, S7-USB 1.33, MPI2/USB V2.81, MPI/DB-Scan V1.01
Included firmware: S7-LAN V2.60, MPI-LAN V2.85, S7-USB 1.33, MPI2/USB V2.81, MPI/DP-Scan V1.01
Enthaltene Firmware: S7-LAN V2.60, MPI-LAN V2.85, S7-USB 1.33, MPI2/USB V2.81, MPI/DB-Scan V1.00
MPI/DP-Scanner integriert
Included firmware: S7-LAN V2.60, MPI-LAN V2.85, S7-USB 1.33, MPI2/USB V2.81, MPI/DP-Scan V1.00
MPI/DP-Scanner included
Enthaltene Firmware: S7-LAN V2.60, MPI-LAN V2.85, S7-USB 1.33, MPI2/USB V2.81
Fehler bei der Geräteauswahl behoben
Included firmware: S7-LAN V2.60, MPI-LAN V2.85, S7-USB 1.33, MPI2/USB V2.81
Error for device-selection revised
Enthaltene Firmware: S7-LAN V2.60, MPI-LAN V2.85, S7-USB 1.33, MPI2/USB V2.81
Fehler beim Backup/Restore behoben
Prüfung auf installierten USB-Treiber bei USB-Produkte integriert
Timeout für Suche per Netzwerk erhöht
Anzeige der bestehenden Konfiguration einer Backupdatei eines Geräts integriert
Anzeige von Busfehlern: Doppelte Adressen, nicht existende Bus-Parameter-Protokolle
Erkennung des RS485-Umsetzer-Modes beim Ansprechen des Gerätes
Hinweis an den Anwender bei der Netzsuche wenn Netzwerk-Karten im DHCP-Mode ohne IP-Adresse existieren
Nach einem fehlgeschlagenen Update wird automatisch nach dem Gerät gesucht
Update-Rückfragen überarbeitet
Included firmware: S7-LAN V2.60, MPI-LAN V2.85, S7-USB 1.33, MPI2/USB V2.81
Fixed backup/restore error
USB-driver-check for USB products integrated
Network-search timeout increased
Display of the existing configuration of a backup file of a device integrated
Display of bus errors: Duplicate addresses, non-existent bus-parameter-protocols
Detection of the RS485-converter-mode when the device is activated
Note to the user when searching for a network if there are network-cards in DHCP-mode without an IP-address
After an unsuccessful update, the device is automatically searched for
Update queries revised
Enthaltene Firmware: S7-LAN V2.59, MPI-LAN V2.84, S7-USB 1.32, MPI2/USB V2.80
Fehler beim Setzen der Betriebsart (Profil) behoben
Konfig- und Statusdialog der Firmware-Version angepasst
Included firmware: S7-LAN V2.59, MPI-LAN V2.84, S7-USB 1.32, MPI2/USB V2.80
Problem/error fixed when setting the operation-mode (profile)
Config- and status-dialog adapted to the firmware version
Enthaltene Firmware: S7-LAN V2.58, MPI-LAN V2.83, S7-USB 1.31, MPI2/USB V2.79
Included firmware: S7-LAN V2.58, MPI-LAN V2.83, S7-USB 1.31, MPI2/USB V2.79
Enthaltene Firmware: S7-LAN V2.58, MPI-LAN V2.83, S7-USB 1.30, MPI2/USB V2.78
Darstellung des PG/PC-Dialogs überarbeitet
Backup/Restore-Funktion für neue Firmware angepasst
Neuer Konfig- und Statusdialog für die neue Firmware integriert, es wurde die Darstellung der WebAnsicht der Ethernet-Produkten angepasst
Verwendung der Busparameter für neue Firmware angepasst
Included firmware: S7-LAN V2.58, MPI-LAN V2.83, S7-USB 1.30, MPI2/USB V2.78
Presentation of the PG/PC-dialog revised
Backup/Restore-function adapted for new firmware
New config and status dialog for the new firmware integrated, the display of the web view of the Ethernet-products has been adjusted
Use of bus parameters adapted for new firmware
Enthaltene Firmware: S7-LAN V2.57, MPI-LAN V2.82, S7-USB 1.29, MPI2/USB V2.77
Fehler beim Lesen des Gerätenamens von USB und seriellen Geräten behoben
Included Firmware: S7-LAN V2.57, MPI-LAN V2.82, S7-USB 1.29, MPI2/USB V2.77
Failure reading of device-name of usb and serial devices solved
Enthaltene Firmware: S7-LAN V2.56, MPI-LAN V2.81, S7-USB 1.28, MPI2/USB V2.76
Hinweis wegen möglichem Kommunikationsabbruch beim Notloader-Update nicht anzeigen
Fehler behoben, wodurch die PPI-Boot-Meldung bei mehreren LAN-Geräten im Netzwerk fälschlicherweise angezeigt wurde
Probleme bei der Suche von Seriellen und USB-Geräten behoben, welche den Fehler 10 nach einem Update melden
Beschränkung der Anzahl an möglichen Netzwerkkarten aufgehoben
Included firmware: S7-LAN V2.56, MPI-LAN V2.81, S7-USB 1.28, MPI2/USB V2.76
Message for possible communication-abort for emergency-loader-update disabled
Error fixed of displaying PPI-Boot-Message for more LAN-devices in the network, which was not correct
Problem for searching of serial or usb-devices, which displays Error 10 after the update
Restriction of count of possible network-cards deleted
Enthaltene Firmware: S7-LAN V2.55, MPI-LAN V2.80, S7-USB 1.27, MPI2/USB V2.75
Firmware-Update, Backup/Restore und andere Konfigurationsänderungen sind nun für Ethernet-Geräte auch während laufender Kommunikation möglich
Problem dass Bootloader-Updates manchmal durchgeführt wurden obwohl nicht nötig gelöst
Dialog für Suche und Geräteauswahl überarbeitet
WebSeite eines Ethernet-Gerätes kann durch Doppelklick auf Gerätebild oder Gerätetyp geöffnet werden
Im "PPI-Boot Aus"-Dialog war ein Ethernet-Gerät selektiert wenn es vorher in der Geräteübersicht deselektiert wurde
Automatische "Gerätesuche" bei Programmstart ist abschaltbar
Anzeige des Backup/Restore-Dialog überarbeitet
Fehler bei der direkten Suche nach einem LAN-Teilnehmer, wenn die IP-Adresse über den VPN-Hinweis-Dialog eingegeben wurde, behoben
Included firmware: S7-LAN V2.55, MPI-LAN V2.80, S7-USB 1.27, MPI2/USB V2.75
Firmware-update, Backup/Restore and other configuration-changes now possible for ethernet-devices while running communication
Problem solved: sometimes a Bootloader-update was done wether it was not neccessary
Dialog for Search and selection of devices revised
WebSite of a ethernet-device can be open directly now with a double-click on the device-icon or type-field
In the dialog of "PPI-Boot Off" was an ethernet-device selected when this device was deselected before
Automatic "search for devices" after programm-start now deactivatable
Display of Backup/Restore-dialog revised
Problem solved for direct ip-search of an ethernet-device when this ip-address was set with the VPN-note-dialog
Firmware S7-LAN V2.54 und MPI-LAN V2.79 integriert
 |
|